Showcase
Models Showcase
Models designed by Krypto, the SO3D robot, and by our members. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
MAIN PURPOSE: Loosen a tight shirt collar under a tie
Button the shirt button through the slot and tilt the T toggle through the collar buttonhole: the collar gains 12 mm, so a shirt that has become tight round the neck closes comfortably under a tie.
Printing notes
0.9 cm³
Volume
1.2 g
Est. weight
860
Triangles
Print flat in PETG; white or clear hides best.
MAIN PURPOSE: Fasten a bracelet with one hand
Spring the C cuff onto your wrist and hook the bracelet end ring over the small hook: the bracelet is held in place while your other hand brings round the clasp, the fiddly part of dressing alone.
Printing notes
11.0 cm³
Volume
13.7 g
Est. weight
2,056
Triangles
Print as it comes (profile on the bed) in PETG.
MAIN PURPOSE: Trim an even beard neckline
Hold the curved guide under the jaw and run the trimmer along its edge: the neckline comes out as one clean, symmetrical curve, the same line every week instead of creeping higher each time.
Printing notes
8.1 cm³
Volume
10.0 g
Est. weight
352
Triangles
Print flat in PETG.
MAIN PURPOSE: Keep mascara off the eyelid
Hold the curved card along the lash line with the thumb tab while you apply mascara: stray strokes land on the shield, not on the eyelid or under the eye, so there is nothing to wipe off afterwards.
Printing notes
2.2 cm³
Volume
2.7 g
Est. weight
368
Triangles
Print flat in PETG; wipe clean.
Shower leg-shaving foot rest
MAIN PURPOSE: Raise a foot safely for shaving in the shower
Stand it on the shower floor against the wall and put one foot on the 15 degree tread: the leg is raised and bent for shaving or washing without balancing on one foot on a wet floor. The trussed profile carries full body weight.
Printing notes
407.6 cm³
Volume
505.5 g
Est. weight
764
Triangles
Print as it comes (profile on the bed) in PETG, 40% infill.
Magnetic under-shelf soap mount
MAIN PURPOSE: Hang a bar of soap on a magnet to dry
Screw the cup under a shelf or the shower caddy, press a 20 x 3 mm magnet into it, and push a steel bottle cap into the back of the soap bar: the soap hangs in the air, dries all round and never sits in a slimy dish again.
Printing notes
2.5 cm³
Volume
3.1 g
Est. weight
848
Triangles
Add a 20 x 3 mm magnet and a steel bottle cap. Prints as shown on its floor, no supports.
Toilet seat lifting tab
MAIN PURPOSE: Lift the toilet seat without touching it
Stick the pad to the underside of the toilet seat near the front: the angled tab gives a finger something to lift, so nobody grabs the rim of the seat itself. Small, discreet and easy to wipe.
Printing notes
11.5 cm³
Volume
14.3 g
Est. weight
408
Triangles
Print as it comes (profile on the bed) in PETG; fix with waterproof tape.
MAIN PURPOSE: Descale a fixed shower head without removing it
Fill the cup with vinegar, lift it up round a fixed shower head and hook a bungee through the side holes over the arm: the nozzles soak overnight and the limescale comes off with a thumb, no unscrewing needed.
Printing notes
47.8 cm³
Volume
59.3 g
Est. weight
4,372
Triangles
PETG with 3 walls so it stays watertight. Prints as shown on its floor, no supports.
MAIN PURPOSE: Pull hair clogs out of basin drains
Feed the 240 mm strip down the plughole and pull it back by the ring: the barbs along both edges catch the clump of hair that slows the drain, so the basin runs freely again without chemicals.
Printing notes
3.3 cm³
Volume
4.1 g
Est. weight
732
Triangles
Print flat in PETG; it flexes round the trap.
