Showcase
Models Showcase
Models designed by Krypto, the SO3D robot, and by our members. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category
Printmaking baren
MAIN PURPOSE: Rub linocut prints by hand
A baren for printing linocuts and woodcuts by hand: grip the bar and rub the smooth, flat underside over the paper to lift an even print from the inked block.
Printing notes
70.3 cm³
Volume
87.2 g
Est. weight
692
Triangles
Prints as shown on its floor, no supports.
Drop spindle whorl
MAIN PURPOSE: Spin your own yarn by hand
A rim-weighted whorl for a drop spindle: press it onto an 8 mm dowel with a hook in the end and spin your own yarn; most of the weight sits at the rim, so it spins long and steady.
Printing notes
18.6 cm³
Volume
23.1 g
Est. weight
848
Triangles
Prints as shown on its floor, no supports.
Mini weaving loom
MAIN PURPOSE: Weave small first projects on a frame
A frame loom for first weaving projects: wind the warp thread round the notches at the top and bottom, then weave across the open window to make a mug rug or a small wall hanging.
Printing notes
52.6 cm³
Volume
65.3 g
Est. weight
1,308
Triangles
Prints flat as a plate, no supports.
Wrist pin cushion base
MAIN PURPOSE: Keep sewing pins on your wrist
The base of a wrist pin cushion: stuff a fabric dome into the cup and thread an elastic or hook-and-loop strap through the two slots underneath, so pins are always at hand while you sew or fit.
Printing notes
13.2 cm³
Volume
16.3 g
Est. weight
1,984
Triangles
Prints as shown on its floor, no supports.
Sewing bobbin ring
MAIN PURPOSE: Display sewing bobbins and hold snips
Sewing machine bobbins stand on edge round a ring channel, so every thread colour shows at a glance; the middle holds a seam ripper and snips.
Printing notes
57.2 cm³
Volume
70.9 g
Est. weight
1,008
Triangles
Prints as shown on its floor, no supports.
Light switch wall plate
MAIN PURPOSE: Cover a toggle light switch
A cover plate for a standard North American single toggle switch, with screw holes 83.3 mm apart and a softly rounded edge; print it in a colour that matches the wall. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
15.6 cm³
Volume
19.4 g
Est. weight
1,996
Triangles
Print floor-down as shown, then turn it over to use it.
Smart speaker pedestal
MAIN PURPOSE: Cradle a spherical smart speaker
A pedestal for a spherical smart speaker about 10 cm across: the rounded inner cove cradles it so it can't roll, and the cable drops through a hole at the back and runs out under the raised feet.
Printing notes
54.2 cm³
Volume
67.2 g
Est. weight
1,228
Triangles
Prints as shown on its floor, no supports.
Compact umbrella stand
MAIN PURPOSE: Dry and separate folding umbrellas
A slim stand for folding umbrellas by the door: four dividers keep up to four apart so they dry, and the drips collect in the closed base.
Printing notes
361.7 cm³
Volume
448.4 g
Est. weight
1,112
Triangles
Prints as shown on its floor, no supports.
Windscreen ice scraper
MAIN PURPOSE: Scrape ice off car windscreens
A flat ice scraper with a wide blade for windscreens and a long, narrow handle that keeps your knuckles off the glass; print it in PETG so it stays tough in the cold.
Printing notes
42.4 cm³
Volume
52.6 g
Est. weight
1,444
Triangles
Prints flat as a plate, no supports.
Bike tyre lever
MAIN PURPOSE: Remove bike tyres from rims
A stiff tyre lever with a spoon tip that slides under the bead and a hooked tail that clips onto a spoke; print two or three in PETG or nylon for the saddle bag.
Printing notes
12.5 cm³
Volume
15.4 g
Est. weight
252
Triangles
Prints flat as a plate, no supports.